Air Line

Air line delivers compressed air that's stored in the air tank, to the bags on each corner of the vehicle. The smaller the air line size, the easier it is to route through the vehicle but the slower the vehicle will raise and lower. Larger air lines are stiffer but allow for more air flow which in turn allows the vehicle to move up and down at a quicker rate of speed. 1/4" and 3/8" air line sizes are the most common for vehicles today.

Air Line Products Browse a collection of Air Line products en

Air Line Clamp
Rating:
0%
0

$2.00

Air Line Clamp https://www.bagriders.com/media/catalog/product/cache/c07d28ad5d149b06f4ee5222c20ececb/a/i/air_line_clamp.jpg Use these camps to neatly route your air lines. Made of 304 stainless steel with neoprene cushions. Air Line Clamp USD 2.00 https://schema.org/NewCondition https://schema.org/InStock https://www.bagriders.com/air-management/air-line/air-line-clamp.html
Aluminum Hard Line (1/4" - 3')
Rating:
75%
4

$20.00

Aluminum Hard Line (1/4" - 3') https://www.bagriders.com/media/catalog/product/cache/c07d28ad5d149b06f4ee5222c20ececb/a/l/aluminium_hardline_2.jpg Thinking about doing a fancy management setup? Hard lines are the key to success. Aluminum hard line is great since the material has less impurities than copper and will give you more consistent bends than copper hard line. Aluminum hard line is still soft enough to get creative without too much effort. Pair a couple 3ft segments of this hard line with a Ridgid 400 Series Hard Line Bender as well as a Hard Line Cutter and go to town! BR08817 USD 20.00 https://schema.org/NewCondition https://schema.org/InStock https://www.bagriders.com/air-management/air-line/aluminum-hardline-1-4.html
Aluminum Hard Line (3/8" - 3')
Rating:
100%
1

$20.00

Aluminum Hard Line (3/8" - 3') https://www.bagriders.com/media/catalog/product/cache/c07d28ad5d149b06f4ee5222c20ececb/a/l/aluminium_hardline.jpg Thinking about doing a fancy management setup? Hard lines are the key to success. Aluminum hard line is great since the material has less impurities than copper and will give you more consistent bends than copper hard line. Aluminum hard line is still soft enough to get creative without too much effort. Pair a couple 3ft segments of this hard line with a Ridgid 400 Series Hard Line Bender as well as a Hard Line Cutter and go to town! BR01020 USD 20.00 https://schema.org/NewCondition https://schema.org/InStock https://www.bagriders.com/air-management/air-line/aluminum-hardline-3-8.html
Bag Riders Air Line Cutter
Rating:
100%
3

$10.00

Bag Riders Air Line Cutter https://www.bagriders.com/media/catalog/product/cache/c07d28ad5d149b06f4ee5222c20ececb/b/a/bag-riders-air-line-cutter.jpg Cutting your air line at a 90º angle is extremely important, especially when it comes to push to connect fittings. These air line cutters are designed to give you the straightest cut to ensure a solid seal. BR00094 USD 10.00 https://schema.org/NewCondition https://schema.org/InStock https://www.bagriders.com/air-management/air-line/air-line-cutter.html
Bag Riders Manifold Hard Line Kit
Rating:
0%
0

$250.00

Bag Riders Manifold Hard Line Kit https://www.bagriders.com/media/catalog/product/cache/c07d28ad5d149b06f4ee5222c20ececb/q/u/quarter-inch-hardline-kit_1_1.jpg You bagged your car, but now you're trying to spice up your trunk setup and make it a little more presentable? Our Manifold Hard Line kit will come with everything you need as a first timer to get started making your own hard line setup and you'll save some money buying it as a bundle! This kit is intended to connect the 6 ports on a traditional air ride manifold to bulkheads in the floor. Since it comes with 6 feet of hardline, you'll have plenty to make these connections, and you can afford a few mistakes. You might even have some left over if you want to connect your tank to your manifold with hardline. Our kit includes aluminum hard lines which seal well with PTC fittings (unlike Stainless Steel hard lines) and can be polished up for a show-worthy shine. Includes: (6) 3 Ft Sections of Aluminum Hardline (1/4" or 3/8") (6) SMC DOT Bulkhead Unions (1/4" or 3/8") (1) Ridgid 400 Series Hard Line Bender (1/4" or 3/8") (1) Hard Line Cutter Bag Riders Manifold Hard Line Kit USD 250.00 https://schema.org/NewCondition https://schema.org/InStock https://www.bagriders.com/air-management/air-line/bag-riders-hardline-kit.html
DOT Air Line
Rating:
100%
7

$0.73

DOT Air Line https://www.bagriders.com/media/catalog/product/cache/c07d28ad5d149b06f4ee5222c20ececb/d/o/dot-air-line.jpg This air line is DOT Approved and is sold by the foot. A quantity of one (1) equals one (1) foot of air line. A quantity of ten (10) equals ten (10) feet of air line. DOT air line is limited to 1/4", 3/8" and 1/2" sizes. For 1/8" air line check out Gauge Air Line. DOT Air Line USD 0.73 https://schema.org/NewCondition https://schema.org/InStock https://www.bagriders.com/air-management/air-line/dot-air-line.html
DOT Air Line (60ft Bundle)
Rating:
100%
9

$35.00

DOT Air Line (60ft Bundle) https://www.bagriders.com/media/catalog/product/cache/c07d28ad5d149b06f4ee5222c20ececb/a/i/air_line_bundle.jpg This air line is DOT Approved and is sold as a 60 foot roll. These 60ft bundles of air line are limited to 1/4" and 3/8" sizes. For 1/8" air line check out Gauge Air Line. DOT Air Line (60ft Bundle) USD 35.00 https://schema.org/NewCondition https://schema.org/InStock https://www.bagriders.com/air-management/air-line/dot-air-line-60.html
Gauge Air Line (1/8 Inch)
Rating:
0%
0

$0.43

Gauge Air Line (1/8 Inch) https://www.bagriders.com/media/catalog/product/cache/c07d28ad5d149b06f4ee5222c20ececb/a/i/air_line_eighth_inch.jpg This air line is used for gauges and should not be used to feed air springs. It is sold by the foot and a quantity of one (1) equals one (1) foot of air line. If you are looking for 1/4", 3/8", or 1/2" air line, check out the DOT Air Line. BR00163 USD 0.43 https://schema.org/NewCondition https://schema.org/InStock https://www.bagriders.com/air-management/air-line/gauge-air-line-1-8-inch.html
Gauge Air Line (1/8 Inch) (50ft Bundle)
Rating:
0%
0

$25.00

Gauge Air Line (1/8 Inch) (50ft Bundle) https://www.bagriders.com/media/catalog/product/cache/c07d28ad5d149b06f4ee5222c20ececb/a/i/air_line_bundle_1.jpg This air line is used for gauges and should not be used to feed air springs. It is sold as a 50 foot roll. If you are looking for 60ft bundles of 1/4" or 3/8" air line, check out the DOT Air Line. BR00427 USD 25.00 https://schema.org/NewCondition https://schema.org/InStock https://www.bagriders.com/air-management/air-line/gauge-air-line-1-8-inch-50.html
Hard Line Cutter
Rating:
100%
1

$12.00

Hard Line Cutter https://www.bagriders.com/media/catalog/product/cache/c07d28ad5d149b06f4ee5222c20ececb/h/a/hard-line-cutter.jpg This hard line cutter is designed to give you square, 90º cuts even close to flared ends. The hardened alloy steel cutting wheel is great for most metals like aluminum, copper, brass, plastic, and mild steel (thin wall). BR02433 USD 12.00 https://schema.org/NewCondition https://schema.org/InStock https://www.bagriders.com/air-management/air-line/hardline-cutter.html
Ridgid 400 Series Hard Line Bender (1/4")
Rating:
100%
1

$100.00

Ridgid 400 Series Hard Line Bender (1/4") https://www.bagriders.com/media/catalog/product/cache/c07d28ad5d149b06f4ee5222c20ececb/r/i/ridgid_400_series_hardline_bender_1.jpg If you're looking to do it right the first time, Ridgid is the way to go. Sure, there are cheaper bender alternatives on the market but the Ridgid 400 Series gives you the control and accuracy you need to make sure you aren't wasting any bends. This hard line bender is designed for bending copper, steel, and stainless steel with a wall thickness less than or equal to 0.06" (1.5 mm) to a maximum of 180°. BR08894 USD 100.00 https://schema.org/NewCondition https://schema.org/InStock https://www.bagriders.com/air-management/air-line/ridgid-400-series-hardline-bender-1-4.html
Ridgid 400 Series Hard Line Bender (3/8")
Rating:
0%
0

$100.00

Ridgid 400 Series Hard Line Bender (3/8") https://www.bagriders.com/media/catalog/product/cache/c07d28ad5d149b06f4ee5222c20ececb/r/i/ridgid_400_series_hardline_bender.jpg If you're looking to do it right the first time, Ridgid is the way to go. Sure, there are cheaper bender alternatives on the market but the Ridgid 400 Series gives you the control and accuracy you need to make sure you aren't wasting any bends. This hard line bender is designed for bending copper, steel, and stainless steel with a wall thickness less than or equal to 0.06" (1.5 mm) to a maximum of 180°. BR02437 USD 100.00 https://schema.org/NewCondition https://schema.org/InStock https://www.bagriders.com/air-management/air-line/ridgid-400-series-hardline-bender-3-8.html

Air Line Videos

1/4" vs 3/8" Air Line Speed Comparison

How much faster is 3/8" air line compared to 1/4" air line? In this video we demonstrate the air out speed difference between the two options. Choosing the right air line for you comes down to personal preference and how quickly you want your air suspension to travel. When it comes to popularity amongst our customers, 1/4" air line is a little more common than 3/8" air line.








Tell us about your Vehicle: